Welcome page
Products
Ozeki 10
Apps
Connections
SMS
Email
Gamepad
Arduino
Analog Sensor
Button
Buzzer
DC Motor
DHT Sensor
Gyroscope
ID Manager
IR Transceiver
Joystick
Keyboard
LCD Display
NFC Reader
Optical Gate
RF 433 MHz
433 MHz Module Info
Arduino Mega 2560
Arduino Nano
Arduino Uno
Ozeki Matrix
Ozeki 433Mhz RF Module
Raspberry PI
Protocol
Chat Control
RF 2.4 GHz
RGB LED
RGB Sensor
Rotary Encoder
Servo Motors
Stepper Motors
Switch Controller
Temperature Sensor
Ultrasonic
Orientation
PBX VoIP Phone
Speech Engines
Split view camera
Autoconnect to Serial
Installation guide
Terms and Definitions
SMS
Bulk Messenger
Cluster
Developer tools
Robots
Hardware
Technology
Company


Ozeki
Ozeki Matrix Ozeki Matrix | Raspberry PI Raspberry PI

Ozeki 433Mhz RF Module

The Ozeki 433Mhz RF Module is a modified Arduino Nano. You can directly plug 433Mhz RF transmitter/receiver modules to it. This is an open source board, with all the files needed for manufacturing. You may also freely modify the design.


Figure 1 - Ozeki 433Mhz RF Module components

You can use the 433 MHz communication with
wireless infrared motion sensors and RF remote controllers:


Video 1 - Shows how to upload code to Ozeki 433Mhz RF Module
Start the video

The Ozeki 433Mhz RF Module contains an ATmega328P microcontroller so you can program it just like an Arduino Nano using the Arduino IDE environment. It has a micro USB port, which is compatible with mobile phone USB cables. It was designed to make it easy to solder in the RF transmitter and receiver parts, and it has standard mounting holes for M2 screws. It is better then using an Arduino Nano, because it is more compact solution, since the RF transmitter and receiver are soldered directly to the board.

Figure 2 - Ozeki 433Mhz RF Module photos

Download files for manufacturing

Datasheets

Specifications

  • IC: ATmega328P
    • Clock Speed: 16 MHz
    • Flash Memory: 32 KB
    • SRAM: 2 KB
    • EEPROM: 1 KB
  • USB support provided by a CH340G USB to serial chip:
  • Power supply from USB (5V)
  • 500mA resettable fuse
  • Status LEDs: power, TX, RX, D13, D10
  • Can be screwed on an Ozeki Matrix Board
  • Product dimensions:
    2.40in.[60.96mm]×0.80in.[20.32mm]
  • Transmitter parameters:
    • Launch distance: 20-200 meters (different voltage, different results)
    • Operating voltage: 3.5-12V
    • Operating mode: AM
    • Transfer rate: 4KB/s
    • Transmitting power: 10mW
    • Transmitting frequency: 433.92 Mhz
    • Transmitter pin: D2
  • Receiver parameters:
    • Operating voltage: 5V
    • Quiescent Current: 4mA
    • Receiver sensitivity: -105DB
    • Receiving frequency: 433.92 Mhz
    • Reciever pin: D3

Pinout of the Ozeki 433Mhz RF Module:


Figure 3 - Receiver and Transmitter pinout of the Ozeki 433Mhz RF Module


Program codes

  • Sends and receives 433 MHz signals

    Simple test

    To simply test this code upload it to an Ozeki 433Mhz RF module and send RF signals to it from outside sources. Here are a few RF sources you can find:

    • Wireless infrared motion sensor
    • RF remote controller

    Test it by sending signals from one Ozeki RF module to another

    To fully test out this code you will need two Ozeki 433Mhz RF modules and upload this code to both modules. One will be the transmitter and the other will be the receiver. The transmitter can transmit any integer value (-32,768 to 32,767). You just need to simply write in the number and press Enter to send. The other one will show the signals arrived on it's serial screen. To communicate with 2 serial ports at the same time you should use multiple Arduino IDEs or use our sophisticately designed software for parallel serial communication: Ozeki Terminal.

    Downloadable code:
    RF_Module_ExampleCode.zip

    #include <RCSwitch.h>
     
    RCSwitch myTransmitterSwitch = RCSwitch(); //repeats transmission 10 times
                                               //uses protocol 1
      
    RCSwitch myReceiverSwitch = RCSwitch(); //repeats transmission 10 times
                                            //uses protocol 1                               
    char inputString[256];
     
    void setup() {
      Serial.begin(115200);
      myTransmitterSwitch.enableTransmit(2); // Transmitter is connected to Arduino Pin D2
      myReceiverSwitch.enableReceive(1);  // Receiver on interrupt 1 => that is pin D3
     Serial.println("Please type any int (-32,768 to 32,767) and press Enter.");
     Serial.println("If data is received the program automatically writes it out.");
    }
     
    void loop() {
      if(Serial.available()){
        delay(1);
        ReadLine();
        myTransmitterSwitch.send(atoi(inputString), 24); //Transmit signal
        Serial.println("");
        Serial.print(atoi(inputString));
        Serial.println(" has been sent.");
        if (myReceiverSwitch.available() &&
              (myReceiverSwitch.getReceivedValue() == atoi(inputString)) )
          myReceiverSwitch.resetAvailable(); //removes transmitted_value from received  
        for(int i=0; i<256; i++)
          inputString[i] = NULL;  
      }
       
       if (myReceiverSwitch.available()) { //Signal received
        int value = myReceiverSwitch.getReceivedValue();
        if (value == 0) {
          Serial.println("Unknown encoding");
        } else {
                Serial.print("Received number: ");
                Serial.println( value );
              }
        myReceiverSwitch.resetAvailable();
      }
       
    }
     
    void ReadLine() {
      for(int i=0; i<256; i++)
        inputString[i] = NULL;
      int i=0;
      while (Serial.available()) {
        inputString[i] = (char)Serial.read();
        if (inputString[i] == '\n') {
          break;
        }
        i++;
      }
    }
    
    Source Code 1 - Arduino example for 433 MHz signal communication


    Video 1 - Watch video to see the code above at work
    Start the video

Other modules

All of the Ozeki Processing Modules have ATmega328P or ATmega2560 microcontrollers integrated. Ozeki Modules can be connected to eachother like pieces of blocks. The connection is provided through USB to each module. They have M2 screw holes to give you an option to screw them on an Ozeki Matrix Board.

See all Ozeki Processing Modules


Copyright © 2000- - Ozeki Ltd | info@ozeki.hu | Tel: +36 1 371 0150
Home > Products > Ozeki 10 > Connections > Arduino > RF 433 MHz > Ozeki Matrix > Ozeki 433Mhz RF Module
Legal | Privacy policy | Terms of use
Page: 1521 | Login | 34.228.30.69