Products
Technology
SMS solutions
PBX systems
Databases
Robotics
Building robot hardware
Building electronics
Building robot software
Introduction/Protocols
Architecture
How to develop a devhandler
Line protocol
DeviceHandlers
Oz433Mhz Transceiver
OzAnalogJoystickController
OzAnalogSensor
OzBatteryController
OzBuzzerController
OzButtonController
OzDCMotorControllerL298N
OzDHTController
OzDoorphoneController
OzEEPROMController
OzKeyboardController
OzGyroscopeSensor
OzIDManager
OzIRTransceiver
OzLCDController
OzNfcReader
OzOpticalGateController
OzRegisterManipulation
OzRF24Transceiver
OzRGBLEDController
OzRotaryController
Example
OzServoController
OzStepCounter
OzStepperMotorMultiController
OzSwitchController
OzTemperatureController
OzTimer
OzUltrasonicSensor
Examples
Bootloader
Company


OzRotaryController

This protocol controls a rotary encoder connected to the microcontroller. Rotary encoders can turn infinite number of rounds. If the rotary encoder turns or the state of the button on the encoder changes, the device sends an event to the .Net. You can use full, half or quarter rotary encoders.

How to build a test circuit with a rotary encoder and an Arduino Mega?
Arduino codes are included.

I. "Welcome" event from microcontroller

Example

c=welcome&type=OzRotaryController&id=IqlZci&pos=2&t=3

Parameters

Parameter Type Range Functionality
c String "welcome" Identifies the welcome message.
type String "OzRotaryController" Determines the type of the device.
id String 6 characters (numbers, uppercase and lowercase characters) The ID of the device which is chosen by the microcontroller.
pos Byte 0-255 Determines the position of the device on the list of the ID manager of the microcontroller. Please make sure there are no other devices in the same position.
t Byte 0-255 Counts the number of events sent combined. Counts from 0 to 255 then from 0 again.



II. Commands to microcontroller

None

III. Event from microcontroller

"Rotary Changed" event

This event is called if the rotary encoder changes direction or the button is pressed or released.

Example

c=rotarychange&button=1&left=0&right=0&id=IqlZci&t=3

Parameters

Parameter Type Range Functionality
c String "rotarychange" Identifies the event.
button Bool 0,1 Button's state (see:OzekiButtonController).
left Bool 0,1 If rotated left, it changes to 1. It is 0 otherwise.
right Bool 0,1 If rotated right, it changes to 1. It is 0 otherwise.
id String 6 characters (numbers, uppercase and lowercase characters) The ID of the device which is chosen by the microcontroller.
t Byte 0-255 Counts the number of events sent combined. Counts from 0 to 255 then from 0 again.

Response

This response is sent from your computer.

c=rotarychange_resp&button=1&left=0&right=0&id=IqlZci&t=1

Parameters

Parameter Type Range Functionality
c String "rotarychange_resp" Identifies the event response.
button Bool 0,1 Button's state (see:OzekiButtonController).
left Bool 0,1 If rotated left, it changes to 1. It is 0 otherwise.
right Bool 0,1 If rotated right, changes to 1. It is 0 otherwise.
id String 6 characters (numbers, uppercase and lowercase characters) The ID of the device which is chosen by the microcontroller.
t Byte 0-255 Counts the number of responses sent combined. Counts from 0 to 255 then from 0 again.
Copyright © 2000- - Ozeki Informatics Ltd. | info@ozeki.hu | Tel: +36 1 371 0150
Home > Technology > Robotics > Building robot software > Introduction/Protocols > DeviceHandlers > OzRotaryController
Page: 1594 | Login