Arduino Buzzer Protocol
This protocol controls a buzzer connected to the microcontroller. Buzzers are capable to play different tones and sequentially combine tones to create music. This protocol contains an easy command to achieve this.
How to build a test circuit with a buzzer and an Arduino Mega?
Arduino codes are included.
I. "Welcome" event from microcontroller
Example
c=welcome&id=A47vvH&type=OzBuzzerController&pos=2&t=3
Parameters
Parameter | Type | Range | Functionality |
c | String | "welcome" | Identifies the welcome message. |
type | String | "OzBuzzerController" | Determines the type of the device. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | The ID of the device which is chosen by the microcontroller. |
pos | Byte | 0-255 | Determines the position of the device on the list of the ID manager of the microcontroller. Please make sure there are no other devices in the same position. |
t | Byte | 0-255 | Counts the number of events and responses sent combined. Counts from 0 to 255 then from 0 again. |
II. Command to microcontroller
"Set Buzz" command
This command orders the buzzer to beeping sound with a frequency and duration provided in the parameters. If the duration is not given than the tone will not change until new command.
Example
c=setbuzz&freq=300&length=1000&t=0&id=A47vvH
Parameters
Parameter | Type | Range | Functionality |
c | String | "setbuzz" | Identifies the command. |
freq | Ushort | 0-65535 | Frequency of the sound. |
length | Ushort | 0-65535 (optional parameter) |
Duration given in millisec. If not given the tone will not change until new command. |
t | Byte | 0-255 | Counts the number of commands sent. Counts from 0 to 255 then from 0 again. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | Identifies the device. The ID is never changed during communication. |
Response
If tone duration was specified than this response will arrive after the tone.
c=setbuzz_resp&id=A47vvH&freq=300&length=1000&t=3
Parameters
Parameter | Type | Range | Functionality |
c | String | "setbuzz_resp" | Identifies the response. |
freq | Ushort | 0-65535 | Frequency of the sound. |
length | Ushort | 0-65535(optional parameter) | Duration given in millisec. If not given the tone will not change until new command. |
t | Byte | 0-255 | Counts the number of events and responses sent combined. Counts from 0 to 255 then from 0 again. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | Identifies the device. The ID is never changed during communication. |
III. Event from microcontroller
None
More information
- بروتوكول تسلسلي لجهاز إرسال واستقبال راديو تردد 433 ميجا هرتز
- بروتوكول تسلسلي للجويستيك التمثيلي
- بروتوكول تسلسلي للمستشعر التمثيلي
- بروتوكول تسلسلي للزر
- بروتوكول تسلسلي للجرس
- بروتوكول تسلسلي لمحرك التيار المستمر
- بروتوكول تسلسلي لمستشعر DHT
- بروتوكول تسلسلي لـ EEPROM
- بروتوكول تسلسلي للوحة المفاتيح
- بروتوكول تسلسلي لمستشعر الجيروسكوب
- بروتوكول تسلسلي لمدير الهوية
- بروتوكول تسلسلي لجهاز إرسال واستقبال الأشعة تحت الحمراء
- بروتوكول تسلسلي لشاشة LCD
- بروتوكول تسلسلي لقارئ NFC
- بروتوكول تسلسلي للبوابة البصرية
- سجل
- بروتوكول تسلسلي لجهاز إرسال واستقبال RF24
- بروتوكول تسلسلي لـ LED RGB
- بروتوكول تسلسلي لمستشعر RGB
- بروتوكول تسلسلي للمشفر الدوار
- بروتوكول تسلسلي لمحرك السيرفو
- بروتوكول تسلسلي لعداد الخطوات
- بروتوكول تسلسلي للمحرك الخطوي
- بروتوكول تسلسلي للمفتاح
- بروتوكول تسلسلي لمستشعر درجة الحرارة
- بروتوكول تسلسلي للمؤقت
- بروتوكول تسلسلي لمستشعر السونار
- رسائل ترحيب لطابعة أوزيكي ثلاثية الأبعاد