Arduino Rotary Encoder Protocol
This protocol controls a rotary encoder connected to the microcontroller. Rotary encoders can turn infinite number of rounds. If the rotary encoder turns or the state of the button on the encoder changes, the device sends an event to the .Net. You can use full, half or quarter rotary encoders.
How to build a test circuit with a rotary encoder and an Arduino Mega?
Arduino codes are included.
I. "Welcome" event from microcontroller
Example
c=welcome&type=OzRotaryController&id=IqlZci&pos=2&t=3
Parameters
Parameter | Type | Range | Functionality |
c | String | "welcome" | Identifies the welcome message. |
type | String | "OzRotaryController" | Determines the type of the device. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | The ID of the device which is chosen by the microcontroller. |
pos | Byte | 0-255 | Determines the position of the device on the list of the ID manager of the microcontroller. Please make sure there are no other devices in the same position. |
t | Byte | 0-255 | Counts the number of events sent combined. Counts from 0 to 255 then from 0 again. |
II. Commands to microcontroller
None
III. Event from microcontroller
"Rotary Changed" event
This event is called if the rotary encoder changes direction or the button is pressed or released.
Example
c=rotarychange&button=1&left=0&right=0&id=IqlZci&t=3
Parameters
Parameter | Type | Range | Functionality |
c | String | "rotarychange" | Identifies the event. |
button | Bool | 0,1 | Button's state (see:OzekiButtonController). |
left | Bool | 0,1 | If rotated left, it changes to 1. It is 0 otherwise. |
right | Bool | 0,1 | If rotated right, it changes to 1. It is 0 otherwise. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | The ID of the device which is chosen by the microcontroller. |
t | Byte | 0-255 | Counts the number of events sent combined. Counts from 0 to 255 then from 0 again. |
Response
This response is sent from your computer.
c=rotarychange_resp&button=1&left=0&right=0&id=IqlZci&t=1
Parameters
Parameter | Type | Range | Functionality |
c | String | "rotarychange_resp" | Identifies the event response. |
button | Bool | 0,1 | Button's state (see:OzekiButtonController). |
left | Bool | 0,1 | If rotated left, it changes to 1. It is 0 otherwise. |
right | Bool | 0,1 | If rotated right, changes to 1. It is 0 otherwise. |
id | String | 6 characters (numbers, uppercase and lowercase characters) | The ID of the device which is chosen by the microcontroller. |
t | Byte | 0-255 | Counts the number of responses sent combined. Counts from 0 to 255 then from 0 again. |
More information
- Protocole série de l'émetteur-récepteur RF 433 MHz
- Protocole série du joystick analogique
- Protocole série du capteur analogique
- Protocole série du bouton
- Protocole série du buzzer
- Protocole série du moteur DC
- Protocole série du capteur DHT
- Protocole série de l'EEPROM
- Protocole série du clavier
- Protocole série du capteur gyroscopique
- Protocole série du gestionnaire d'ID
- Protocole série de l'émetteur-récepteur IR
- Protocole série de l'écran LCD
- Protocole série du lecteur NFC
- Protocole série de la barrière optique
- Registre
- Protocole série de l'émetteur-récepteur RF24
- Protocole série de la LED RVB
- Protocole série du capteur RVB
- Protocole série de l'encodeur rotatif
- Protocole série du moteur servo
- Protocole série du compteur de pas
- Protocole série du moteur pas à pas
- Protocole série de l'interrupteur
- Protocole série du capteur de température
- Protocole série de la minuterie
- Protocole série du capteur ultrasonique
- Messages de bienvenue de l'imprimante 3D Ozeki